a Virtual Robotix Network Team

VR Gimbal : User Group


VR Gimbal : User Group

Dear Friends ,

after presentation of our new product : VR Gimbal we recive a lot of request about the price , availability and technical info.

In this group could be possible to discuss about VR Gimbal Join us

Members: 68
Latest Activity: Jun 17, 2016

Discussion Forum

VR Gimbal : Mecatronix Gopro

Started by Roberto Navoni. Last reply by Dave von Feb 3, 2014. 5 Replies


Mode changing during flight

Started by Jens Jan 3, 2014. 0 Replies

Hi, is it possible to change the mode-setting during the flight via remote control? Iam searching around and can not find any solutions for that.Also i am searching for a brief description of the…Continue

VR Gimbal Board Rev2 schematics?

Started by DG Oct 4, 2013. 0 Replies

Are the schematics  for the rev2 VR gimbal board available anywhere? I haven't been able to locate them so far. Without the schematics, it's difficult to work with the board.Continue

VR Gimbal and Filmography application .

Started by Roberto Navoni. Last reply by Martin Horak Jul 28, 2013. 2 Replies

VR Gimbal Controller will not only developed for in Drone application but could be also use in standard Video and Filmography application , put inside this discussion thread all your suggestions.In…Continue

Comment Wall


You need to be a member of VR Gimbal : User Group to add comments!

Comment by Conway Vidal on June 18, 2014 at 2:57am

Hi, I am somewhat new here.  I purchased a VR Gimbal controller a few months back but haven't had a chance to test it out till now.  I am liking what I see but for some reason I can't get the IMU Calibration to stick.   I can go through the calibration procedure in the different orientations and it stays level until I power down and restart.  Then it has a slight tilt again.  I feel I may be missing something.  Did all the save functions I could find but it won't stick.   Any help is appreciated.  Thanks.

Comment by Roberto Navoni on March 13, 2014 at 6:28pm

We are doing some test on follow frame on a big gimbal ... this is the result . In this video work fine also the joystick for manual control ...

Comment by Roberto Navoni on March 13, 2014 at 6:26pm

@Denny ,

you can reinstall using dfu utility as for VRBrain ... if you need support can ask to Paolo Masa in Laser Navigation ...

Comment by Denny Rowland on March 4, 2014 at 9:54am

That is what I was thinking but how do I reinstall it?

Comment by Roberto Navoni on March 4, 2014 at 3:29am
Hi denny ... con you bee lost the bootloader
Comment by Denny Rowland on March 3, 2014 at 4:55pm

The Error message is :

lost device after reset. assuming prod-ID was incremented by one. No DFU capable USB device found (VRGimbal 1.13c)

Comment by Denny Rowland on March 3, 2014 at 4:42pm

Further to what I just wrote I see both red and green light when USB is connected . I don't know what the reset button is used for.

Comment by Denny Rowland on March 3, 2014 at 4:33pm

Don't know if anyone else is having problems but I cant get any sense out of my gimbal boards. The Firmware update tools just keeps giving me an upload error. I have it set to Com2 and the device manager looks as it should. The driver (maple R3 COM2) It defaults to 9600 baud rate. Tried it at (115200) Tried with USB and Serial. I don't know if any code is uploaded from new but the GUI does not respond but it sees the com port. I have GUI0.13 and 1.13c

Any Ideas guys? 

Comment by Roberto Navoni on February 6, 2014 at 3:41am

Randy join us in test and developing of VRGimbal ... add in the APM Copter some instruction for inteconnect the board tp APM Boards.

Comment by Roberto Navoni on February 6, 2014 at 1:43am

Some interesting updates on the project :

We update the repository with last revision of source code :

so if other guys want join us in development is welcome ... 


Members (67)



© 2019   Created by Roberto Navoni.   Powered by

Badges  |  Report an Issue  |  Terms of Service