FOXTEAM UAV CLAN

a Virtual Robotix Network Team

VR Gimbal : User Group

Information

VR Gimbal : User Group

Dear Friends ,

after presentation of our new product : VR Gimbal we recive a lot of request about the price , availability and technical info.

In this group could be possible to discuss about VR Gimbal Join us

Members: 68
Latest Activity: Jun 17, 2016

Discussion Forum

VR Gimbal : Mecatronix Gopro

Started by Roberto Navoni. Last reply by Dave von Feb 3, 2014. 5 Replies

Continue

Mode changing during flight

Started by Jens Jan 3, 2014. 0 Replies

Hi, is it possible to change the mode-setting during the flight via remote control? Iam searching around and can not find any solutions for that.Also i am searching for a brief description of the…Continue

VR Gimbal Board Rev2 schematics?

Started by DG Oct 4, 2013. 0 Replies

Are the schematics  for the rev2 VR gimbal board available anywhere? I haven't been able to locate them so far. Without the schematics, it's difficult to work with the board.Continue

VR Gimbal and Filmography application .

Started by Roberto Navoni. Last reply by Martin Horak Jul 28, 2013. 2 Replies

VR Gimbal Controller will not only developed for in Drone application but could be also use in standard Video and Filmography application , put inside this discussion thread all your suggestions.In…Continue

Comment Wall

Comment

You need to be a member of VR Gimbal : User Group to add comments!

Comment by amit regev on August 15, 2015 at 10:46am

I wish to control the multirotor with the camera.

the multirotor will follow where i point the camera.

How can i connect the gimbal attitude to the pixhawk?

Comment by Erik Wittenzellner on November 28, 2014 at 4:17am
Handheld for a large camera / lens combo. Could be 5 to 8 kg of equipment.
Comment by Erik Wittenzellner on November 28, 2014 at 4:12am
Handheld for a large camera / lens combo. Could be 5 to 8 kg of equipment.
Comment by Erik Wittenzellner on November 28, 2014 at 4:12am
Handheld for a large camera / lens combo. Could be 5 to 8 kg of equipment.
Comment by Roberto Navoni on November 28, 2014 at 2:27am

Hi Erik,

the current is 5 Amp x driver the maximum voltage is 4S . Do you intend develop a hand held gimbal or gimbal for drone ? 

here : vrgimbal.wordpress.com there are more detail about the board.

best

Roberto

Comment by Erik Wittenzellner on November 28, 2014 at 12:09am
What current will this drive? 8000 series motors ok?
Comment by Erik Wittenzellner on November 27, 2014 at 8:56pm
Just purchased the 3axis board and was looking for the optional 9150 board mentioned but could not find it in the shop. Where can i get them? Can't wait to try this out. Need to get some motors now. I'm looking to use this for a Black Magic Cinema Camera. Any suggestions on some motors?
Comment by Roberto Navoni on September 14, 2014 at 11:29pm

New revision 1.19 is online ... we are working to put potentiometer in control loop a new feature available in Zenmuse but will be available soon on VRGimbal ,too

Comment by Roberto Navoni on August 26, 2014 at 8:52pm

Hi , 

tomorrow will be upload the new revision of firmware . The revision is 1.16 The main update is on motor control loop now the resolution is 4096 and is possible to set the PID in micro second and not in millisecond as in previous version . 

Here some test doing today in our lab : 

https://www.youtube.com/watch?v=zyqV9IuHPaE&feature=youtu.be

https://www.youtube.com/watch?v=muhCAIzpF-0&feature=youtu.be

best

Roberto

Comment by Conway Vidal on June 21, 2014 at 6:07pm

Is this product not supported anymore?

 

Members (68)

 
 
 

Events

© 2017   Created by Roberto Navoni.   Powered by

Badges  |  Report an Issue  |  Terms of Service